News

The J&T Flat Top Titanium line of screws are crafted for style and strength. Manufactured from Grade 5 6Al4V certified titanium these screw packs are a great way to choose where you would like to shed un-wanted weight on your rides, while making them look as great as possible. Our screws are NOT a generic screw anyone can just order, they have been designed in house with a unique design, and tight tolerances only available from J&T! 

• Machined to our unique flat top design
• Includes 4pcs per pack
• Machined for 2mm Allen wrench
• Multiple lengths available
• Natural Titanium and Oil Slick Titanium finishes available

J&T Introduces stackable universal chassis weight

The J&T universal brass chassis weight is a simple chassis weight full of features. First is the 5.5mm broach that will hold a nut while attaching to your chassis with a screw. Next up is the universal design to fit most* vehicles, and lastly is the option to fine tune by adding our 5g stackable weight on top.

To install just insert an M3 screw through the bottom of your chassis and through the weight, the chassis weight already has 5.5mm broach ready to hold the nut while you tighten the screw.

• Available in 5g, 15g, and 30g
• J&T 5g stackable weights can be added
• 5.5mm broach to hold nut
• J&T laser logo and weight

Easily add +20g to the rear of your Mugen MBX8R vehicle by swapping out the stock aluminum C block and replacing it with our brass version.

• Added material around pill for strength
• Black coating
• J&T laser etched logo

The J&T Aluminum center diff top plate for the NB series of Tekno vehicles was designed to reduce flex during hard braking. The 7075-T6 aluminum top plate is much stronger and more ridged then the stock plastic top plate providing a more accurate brake feel and settings. The top plate also features two 5x8x2.5 flanged ball bearings for the brake cams to easily rotate and reduce any slop.

• High Quality 7075-T6 Aluminum
• Better brake performance 
• Ball bearings for brake cams
• Black anodized
• J&T laser etched logo

The new J&T Engine mount for Tekno RC vehicles has the best features from all versions of the engine mount rolled up into one package! The V2 version has been beefed up and just looks a lot better. The mount also gives you the option to run the Tekno clutch or most other clutches on the market. This specific model had been designed to let the car flex more evenly on each side of the chassis.

Choose from Adjustable blocks (Fits stock Tekno Clutch and most aftermarket 3 shoe clutches), or single blocks (Fits Protek/J&T 4 shoe clutches).

• 4 piece design (Includes spacer for fuel tank)

• Optional mounting holes to run stock clutch or aftermarket

• Chamfered Edges

• Top hardware included

• Black anodizing with laser etched logo

• Fits the Tekno NB 48 series

Kyosho MP10 and Xray XB8 '24 Skid Plates added to the J&T line up.

Always thinking of the racer, J&T is proud to introduce our chassis saving skid plates. These skid plates are made from high quality stainless steel with a laser etched J&T logo. When you race on hard abrasive or rocky surfaces your chassis can wear out prematurely, our skid plates are an inexpensive option to save you hundreds of dollars!

• Money saving skid plates save your chassis
• Laser etched logo

The J&T Tekno Adjustable Ackerman Plates are a great upgrade for durability, adjustability, and of course looks. Machined from 3mm thick 7075 aluminum these plates can handle much more abuse then carbon fiber. The added steering adjustment is a plus for those looking for a little more tunability on the car.

• 7075 Aluminum
• Black anodized with silver chamfered edges
• Additional adjustment hole
• J&T laser engraved logo
• Sold in a pair

With the popularity of our Phantom truggy tire growing around the country, we have decided to add them to our extensive lineup of high quality pre-mounted tires. Now available in both white and yellow wheels, with compounds ranging from SS, S, SSLW, SLW, and Clay.

Along with the addition of the full Phantom lineup, we have also added Truggy Clay compounds to the pre-mount family. Now available, the Talon and Raptor in clay compound. Available in both white and yellow wheel pre-mount varieties.

The ProMotion Advanced Cell insert designed specifically for high grip surfaces is an industry first. The blank insert has been specifically designed to perform better in many ways on high grip surfaces.

Traditionally increasing the foam hardness and density for high grip surfaces does increase stability and predictability. But going to hard can have negative effects, and that's what we have fixed. When finally getting a hard enough insert with the traditional design to perform in high grip, you loose forward bite, and traction when needed, and if there are lower grip sections you will find a lack of lateral side bite.

Our insert has been designed to provide lateral stability in high grip, and still maintain good forward bite and traction when needed. We accomplished this by keeping the same foam density and hardness as our traditional foams and removing all relief cuts. All of this has resulted in better high speed lateral stability, better landing compression, and little to sacrifice in forward grip.

• Increased lateral stability in high grip
• Little to no forward bite loss
• More stable landings
• Blank foam can be customized to conditions
• Includes 4 Inserts

The J&T Sparko F8 Adjustable Ackerman Plates are a great upgrade for durability, adjustability, and of course looks. Machined from 3mm thick 7075 aluminum these plates can handle much more abuse then carbon fiber. The added steering adjustment is a plus for those looking for a little more tenability on the car.

• 7075 Aluminum
• Black anodized with silver chamfered edges
• Additional adjustment hole
• J&T laser engraved logo
• Sold in a pair

Promotion 1/10 wheels were designed with durability and lightweight features in mind. Made from our harder wheel material to meet the demands of today's high grip tracks. Lightweight rib design on the inside of the wheels provide the strength needed while not adding un-necessary weight.  Advanced manufacturing processes used to achieve a balanced and true wheel. Small lightweight inner rib on the mounting surface and integrated vent holes make these wheels the perfect choice.

• Lightweight inner rib design
• Vent holes integrated in wheel
• Hard wheel material
• Sold in convenient packs of 4
• Available in White and Flo Yellow

 Includes 4 wheels

The J&T Bearing Co. Leading Edge Rear Wing is designed to keep up with today's changing track surfaces and aerodynamic advantages! The single vertical directed side boards allow for advantages on high speed, higher grip tracks. The base of the wing feature multiple levels that transition to a tall rear dam that features dimples for easy hole layout locations. 

Features

• Long life and flexibility

• Vertical tall side dams

• Tall center dividers for a more stable feel

• Dropped base of wing to lower the center of gravity

• Dimples on wing for optional air flow holes

• Grid for hole layout to work with any wing mount

The J&T Titanium lower shock screw set features 2 RHT and 2 LHT screws. These stylish screws are un-like any others currently available with a unique design on the 5.5mm hex head. The LHT screws are marked with 6 dimples around the face of the screw. Along with being lightweight and stylish these screws will also last longer than the stock aluminum versions that wear out, and cause excessive slop in the shock action.

• Titanium Grade 5 6Al4V certified
• Center Dimple for easy droop measurements
• Machined for 5.5mm nut driver
• Unique head design

The J&T Titanium “Milled” XD Turnbuckles feature a 3.5mm Milled center that tapers down seamlessly for a timeless look that will elevate any vehicles appearance! Unlike most “Finned” designed turnbuckles on the market, our turnbuckles are beefed up with a 4mm center as well as manufactured from a higher GR5 titanium that will take a beating. The J&T titanium turnbuckles are also produced with standard right and left hand threads to work with existing stock rod ends. Includes 1/8'' drill bit to drill out standard rod ends.

Looking for a custom color? Contact Walliebuilds at Info@wbfactoryracing.com

• Milled design for timeless looks

• Upgraded 3.5mm XD size

• GR5 Titanium for strength

• Standard threads to fit stock rod ends

• Multiple colors

Be the envy in the pits with the Pro Motion RWB Hoodie. Show support for your favorite tire company by wearing this quality Hoodie. Featuring the Pro Motion "P" offset on the front chest in a red, white, and blue Camo design. The back of the Hoodie features our original Pro Motion logo below the eye popping large "P" logo!

• 100% pre-shrunk cotton

• Premium Fit

• Hooded with Pull Strings